Oneballjay Pit Stop Kit
Een tooltje, kantenslijper, rub-on wax, braamsteentje en een hadnige
Product number:
022099745747
P
You get 50 bonus points for this order
Product information "Oneballjay Pit Stop Kit"
The Pit Stop Kit is what you need to get your equipment dialed in and ready to go quickly.
The Pit Stop Kit contains:
F-1 All Temp Rub On Wax 85g, ceramic stone, durable pouch, edge sharpener, pocket screwdriver, and complete instructions.
Rub-On Wax Instructions:
1. Dry base
2. Warm base if possible (easier to wax)
3. Wear a glove for edge protection
4. Rub Wax into base with pressure. Apply to completely cover.
5. Use cork to polish wax into base.
6. Lightly scrape off (if possible)
7. Lightly brush out or polish to remove extra wax
Waxing, Scraping, Iron Instructions:
1. Select correct temperature specific wax by checking mountain conditions/snow report... (actual snow temperature, not air).
2. Press wax on the iron and distribute small drips of wax over the entire base. DO NOT ALLOW IRON TO SMOKE!
3. With iron in hand, slowly pull the iron over the wax drips smoothing them into a sheet of wax that covers the entire base tip to tail.
4. Let the wax cool 10-15 minutes, then scrape with a sharp plastic scraper. DO NOT USE a steel scraper.
5. Use a wax brush or fiber pad, remove excess wax from base, brushing from tip to the tail. This allows your base to glide fast.
Tuning Instructions:
1. Place board or skis in a vise to secure and clean base with a fresh hot wax job and scrape or use ONEMFG Base Cleaner.
2. Check the side and base edges for burrs. Rub a ceramic, diamond or gummy stone over the area to remove burrs in preparation for edge shaping.
3. Use the ONEMFG edge tool to sharpen side edges. Start from the tip and pull smoothly with firm pressure to the tail. Do this in smooth passes until the edges are sharp. Repeat on the other side. Remember to flip the file around so that the teeth face the proper direction...look for the arrow.
4. If you like your board or skis to be catch-free in the tip and tail, then de-tune using a de-burring stone to round the edges on the tip and tail. Start on the edges as they curve up into the tail and nose and file down approx. 1.5" past the edge contact point as your base lays flat.
5. For really sharp edges, take a fine diamond stone or polishing stone and go over the edge again using the same technique.
6. If you like to jib rails and boxes, don't sharpen your edges much to keep them catch frees
Keep your edge tool clean with the file brush!
Enjoy your speed!
The Pit Stop Kit contains:
F-1 All Temp Rub On Wax 85g, ceramic stone, durable pouch, edge sharpener, pocket screwdriver, and complete instructions.
Rub-On Wax Instructions:
1. Dry base
2. Warm base if possible (easier to wax)
3. Wear a glove for edge protection
4. Rub Wax into base with pressure. Apply to completely cover.
5. Use cork to polish wax into base.
6. Lightly scrape off (if possible)
7. Lightly brush out or polish to remove extra wax
Waxing, Scraping, Iron Instructions:
1. Select correct temperature specific wax by checking mountain conditions/snow report... (actual snow temperature, not air).
2. Press wax on the iron and distribute small drips of wax over the entire base. DO NOT ALLOW IRON TO SMOKE!
3. With iron in hand, slowly pull the iron over the wax drips smoothing them into a sheet of wax that covers the entire base tip to tail.
4. Let the wax cool 10-15 minutes, then scrape with a sharp plastic scraper. DO NOT USE a steel scraper.
5. Use a wax brush or fiber pad, remove excess wax from base, brushing from tip to the tail. This allows your base to glide fast.
Tuning Instructions:
1. Place board or skis in a vise to secure and clean base with a fresh hot wax job and scrape or use ONEMFG Base Cleaner.
2. Check the side and base edges for burrs. Rub a ceramic, diamond or gummy stone over the area to remove burrs in preparation for edge shaping.
3. Use the ONEMFG edge tool to sharpen side edges. Start from the tip and pull smoothly with firm pressure to the tail. Do this in smooth passes until the edges are sharp. Repeat on the other side. Remember to flip the file around so that the teeth face the proper direction...look for the arrow.
4. If you like your board or skis to be catch-free in the tip and tail, then de-tune using a de-burring stone to round the edges on the tip and tail. Start on the edges as they curve up into the tail and nose and file down approx. 1.5" past the edge contact point as your base lays flat.
5. For really sharp edges, take a fine diamond stone or polishing stone and go over the edge again using the same technique.
6. If you like to jib rails and boxes, don't sharpen your edges much to keep them catch frees
Keep your edge tool clean with the file brush!
Enjoy your speed!
Brand "OneBallJay"
OneBallJay is een ijzersterk snowboard waxmerk. Met goede wax voor alle temperaturen glijd je als een raket van de piste. Daarnaast heeft OneBall de grappigste traction pads, oftewel anti-slip voor je snowboard, maar ook handige snowboard tools, waxijzers en andere snowboard onderhoud materialen. Alles te koop in onze snowboardwinkel in Den Bosch.
Shipping options and costs
DPD is our standard shipping method, but you can also choose one of our other shipping options. Below you will find all the options, including the estimated shipping time. The shipping costs are always stated in the checkout before you complete your order.
| Shipping method | Shipping time | Shipping costs |
|---|---|---|
| DPD Classic | The Netherlands: order before 16:00, delivery next working day. België: order before 16:00, delivery next working day. Delivery on residential addresses Monday to Saturday. Delivery on business addresses Monday to Friday. |
€5,- for orders under €50,- Free for order from €50,- |
| DPD letterbox package |
The Netherlands: order before 16:00, delivery next working day. België: order before 16:00, delivery next working day. Delivery on residential addresses Monday to Saturday. Delivery on business addresses Monday to Friday. |
€5,- for orders under €50,- Free for order from €50,- |
| DPD Parcelshop | The Netherlands: order before 16:00, delivery next working day. België: order before 16:00, delivery next working day. Neem contact met ons op voor de mogelijkheden. |
€5,- for orders under €50,- Free for order from €50,- |
| Pickup at the shop | After ordering you will receive an email that your product(s) are ready for pickup. You can pick up your package at the shop during our opening hours. |
Always free |
| PostNL | The Netherlands: order before 16:00, delivery next working day. België: order before 16:00, delivery within 1-2 working days. Delivery on Monday to Saturday. |
€7,- for orders under €100,- €2,- for orders from €100,- |
| Same Day Delivery |
Netherlands: order before 10:00, delivery on the same day. |
€15,- for orders under €100,- €7,- for orders from €100,- |
More articles from OneBallJay to look at
